Cisco switch temperature command

This software release supports the router features listed in the section Supported Products. Use this document in conjunction with other router software configuration documentation. Connected Grid Documentation Feedback Form. Temperature and Voltage Monitoring TVM is a software feature that provides support for monitoring the router operating temperature and the router power supply voltage.

This section describes the TVM feature and includes the following topics:. During normal operation, the router hardware uses sensors to measure the internal temperature of critical router components, including the central processor and any installed interface cards.

The router uses the individual component temperatures to calculate its operating temperature. Using TVM, you can configure the router with maximum and minimum operating temperatures, called thresholds, to define an operating temperature range for the router.

You can then configure the router to send a notification when it detects that the operating temperature is out of the defined range. Notifications can be in the form of system log messages or SNMP notifications. The section Configure Operating Temperature Monitoringprovides instructions for configuring this functionality. TVM supports power supply monitoring features that are similar to the operating temperature monitoring features. You can configure voltage ranges for the router power supply and then configure notifications to be sent when the power supply voltage is out of the defined range.

The section Configure Power Supply Monitoringprovides instructions for configuring this functionality. The power supply voltage threshold range supported by TVM is different for each power supply model used with the router. For detailed information about these power supplies, refer to the router hardware installation guide.

cisco switch temperature command

TVM supports historical data collection and storage for temperature and voltage. You can configure the router to save historical data about the router operating temperature and power supply voltage. Related features include:. These sections provide instructions for configuring historical data collection:. This section describes how often the router monitors and stores temperature and voltage data. Monitoring Interval —The router checks the operating temperature and power supply voltage once per minute.Note For complete syntax and usage information for the commands used in this chapter, see the switch command reference for this release.

The switch software monitors switch conditions on a per port or a switch basis. If the conditions present on the switch or a port do not match the set parameters, the switch software triggers an alarm or a system message. You can configure the switch to trigger an external alarm device by using the alarm relay.

For more information on how to configure the alarms, see the "Configuring Switch Alarms" section. The switch processes alarms related to temperature and power supply conditions, referred to as global or facility alarms. The switch monitors dual power supply levels. If there are two power supplies installed in the switch, an alarm triggers if a power supply fails. The alarm is automatically cleared when both power supplies are working.

You can configure the power supply alarm to be connected to the hardware relays. For more information, see the "Configuring the Power Supply Alarms" section. The switch contains two temperature sensors that monitor the environmental conditions inside the switch. It cannot be disabled. By default, the primary temperature alarm is associated with the major relay.

The secondary alarm is disabled by default. For more information, see the "Configuring the Switch Temperature Alarms" section. The Ethernet standard calls for a maximum bit-error rate of 10 The bit error-rate range is from 10 -6 to 10 The bit error-rate input to the switch is a positive exponent. If you want to configure the bit error-rate of 10 -9enter the value 9 for the exponent. By default, the FCS bit error-rate is 10 You can set the FCS error hysteresis threshold to prevent the toggle of the alarm when the actual bit-error rate fluctuates near the configured rate.

The hysteresis threshold is defined as the ratio between the alarm clear threshold to the alarm set threshold, expressed as a percentage value. For example, if the FCS bit error-rate alarm value is configured to 10 -8that value is the alarm set threshold. The FCS hysteresis threshold is applied to all ports on the switch. The allowable range is from 1 to 10 percent. The default value is 10 percent.

To save user time and effort, it supports changeable alarm configurations by using alarm profiles. You can create a number of profiles and assign one of these profiles to each Ethernet port. Alarm profiles provide a mechanism for you to enable or disable alarm conditions for a port and associate the alarm conditions with one or both alarm relays. You can also use alarm profiles to set alarm conditions to send alarm traps to an SNMP server and system messages to a syslog server.

The alarm profile defaultPort is applied to all interfaces in the factory configuration by default. Note You can associate multiple alarms to one relay or one alarm to both relays.Go to Solution.

Hello Vineet! I hope you're doing great. That's why you see a major value for this temperature and the corresponding thresholds. Status Green indicates the temperature is normal or the device is not heating up and has good airflow. Yellow represents a warning the temperature is going high than normal. Red is when there might not be sufficient airflow or the device is heating up because of other external or internal factors and need to check the environment around the switch.

View solution in original post. Buy or Renew. Find A Community. We're here for you! Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for. Did you mean:. Cisco tempreture details. Labels: LAN Switching. I have this problem too. Accepted Solutions. Cisco Employee. Re: Cisco tempreture details. I hope you find this information useful.

Regards, View solution in original post. Latest Contents.It is the overall system temperature. Its how hot the box is running. The switch may experience an abnormal increase in temperature. This increase can be confirmed by the show environment temperature command. If the output shows red as the temperature state or the temperature value goes beyond the threshold value, then the recommended action is to prevent the switch from overheating. Center of theSwitch or processor? Buy or Renew. Find A Community.

We're here for you! Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for. Did you mean:. John Katsoulas.

Hi everybody, with the config command 'show environment temp status' you get to see a "System temperature from the Switch. Labels: Other Switching.

cisco switch temperature command

I have this problem too. Reza Sharifi. VIP Expert.

High Temperature Issues The switch may experience an abnormal increase in temperature. Latest Contents. Hello, I will be configuring OSPF for routing and failover between 2 data centers and would like your input on best practice in my case. Attached is the layout. We already have one circuit between the 2 DCs and we are adding another one for redundancy. Created by Santosh Sharma on PM.

EEM script in this case can be challenging because of following reasons: 1. RP reload Created by hiarteag on AM.There are all kinds of news and information related to Cisco and Cisco network equipment, such as release of Cisco equipment, news of Cisco's new networking solution, and Cisco hardware and software upgrading The Cisco Catalyst switch is a small switch that runs the same Cisco IOS that the larger switches do, and has most of the same features.

This article describes several ways you can pull information from the switch, such as the chassis temperature.

cisco switch temperature command

These methods should work on most Cisco switches. Computer with terminal emulation software prepared before you start.

Cisco Show Interfaces Command

Verify you are in the "Privilege Exec" mode, which uses a " " at the end of the prompt. Enter the command "enable" to move out of the "Exec" mode and into the "Privilege Exec" mode. Enter the command "show env all" to see all the environment information.

cisco switch temperature command

Modify the "Yellow Threshold" with the command "system env temperature threshold" followed by a number. This command must be issued from the "config" mode, which has " config " at the end of the prompt. To move from the "Privilege Exec" mode to the "config" mode, issue the command "configure terminal. See Section 1 for details on how to get there.

To disable the HTTP service, issue the command "no ip http server. Open a browser, type the IP address of your switch into the address bar and hit enter. Check the far right section titled "Temp" for the temperature of the switch. Enabling the HTTP service on your switch introduces a security risk.

Reference from Cisco. Catalyst Switch Software Configuration Guide. Home Contact. Share this post. Repost 0. Subscribe to newsletter To be informed of the latest articles, subscribe:.The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared default configuration.

If your network is live, make sure that you understand the potential impact of any command. Refer to Cisco Technical Tips Conventions for more information on document conventions. The MIB provides this description:. Query the device for the entSensorValue 1. In this example, the device host name is zatar :.

For example, what does the index 9. In order to find out, you must go up one level in the tree. Jump one level from 1. This brings you to the entSensorValueEntry 1. The description shows that this OID uses indexes, as you see in the snmpwalk, and so on. From this description, you can again go one step back in the tree and conclude that the entPhysicalIndex comes from the entPhysicalEntry.

Query for the entPhysicalIndex 1.

How to Find the Chassis Temp of a Cisco Catalyst 2960?

Now, you have linked the indexes to the description and linked the indexes to the temperature values. The range can be in one of these stages:. The current status range option in the SNMP notification trap specifies in which of these three ranges of temperature the module lies.

The check duration option in the SNMP notification trap specifies the time duration for which the temperature of the switch is above the normal range. If the current status of the temperature at the test point of the module is at the shutdown stage, the switch automatically shuts down the module. The suggested workaround to avoid unexpected issues is to ensure that the temperature around the switch is kept within the operational standards that the Module Specifications specify.

See the Output of the show environment temperature Command Through the CLI section of this document in order to make this temperature determination. Also, be sure that the internal fans in the switch work normally. Contents Introduction.This was the best service I've ever experienced. Everyone was nice, everything was simple, and I had the best vacation of my life (despite the uncooperative weather). Our trip was amazing. The hotels and day trips were all very good.

Cisco IE 3000 Software Configuration Guide, Release 12.2(58)SE

Hilmar was brilliant before we flew out to Iceland. Always very quick to respond, friendly and very informative with any questions we had. Was so lovely to have a bottle of champagne and lovely chocolates waiting for us in our room when we arrived. It made the start to our honeymoon very special.

We even got to see the Northern Lights too on our second attempt. Superb holiday - thank you so much. We found the whole experience excellent.

How To Get the Environment Temperature on a Catalyst 6500/6000 Using SNMP

There was a lot of driving, yet stress free apart from a blizzard. Doing a circular tour of the country was so interesting, after the first day we thought it may be a case of "same as" but every day was different and enjoyable. We were lucky 3 nights with the "lights" and some beautiful sunny days wonderful sights and beautiful countryside. We have not hesitated to tell others of our experience and now find some friends and family have now added it to their 'bucket list'. Hilmar made scheduling the trip very easy.

The emails were very prompt and once we arrived, we were able to continue adding activities at the last minute with no trouble. The buses to and from sites were very nice and the guides were all so enthusiastic and friendly. Iceland is beautiful in the winter.

The staff and quality of the tour and accommodation made it an excellent experience of Iceland. Iris Angela did a wonderful job putting it together for us. We all have great memories of our trip. Everything was truly wonderful. The trip was amazing from the very beginning. From our pick up at Keflavik to our departure home, the tours were all amazing. Signy did an amazing job, and the added champagne and chocolates when we arrive (we were there for our honeymoon) were just so sweet.


thoughts on “Cisco switch temperature command

Leave a Reply

Your email address will not be published. Required fields are marked *